Andy, I doubt any suction cup will hold. I have a RAM mount bolted to the right of the radio. I made an aluminum holder for the iPad as I could not find one that would hold it with the protective case

Ok I am about to prime and paint my Trailing Edge Fences and Vortolons. I could just lay them on a plastic covered table or drill a small hole in them somewhere to hang them on a wire. If this is the

Hello Mike, I hot glued stir sticks to the mounting bases, and then hot glued to the stir sticks to a piece of 2x4. After priming, painting, and drying I removed the glue from the vortilons and then m

Pieces of double sided tape on piece of rood like 2x4 or 2x2. -- Bulent Aliev Enginegear ph +1 954.557.1019 fax +1 386.957.4473 Bulent@... www.enginegearonline.com

Folk: Thanks to Mike Beasley, the latest COBA newsletter index is available here: http://cozybuilders.org/ref_info/ Happy index searching (and Kwanzaa, of course). -- Marc J. Zeitlin marc_zeitlin@...

There was some recent recent chat about Earth X LiFePo batteries buried towards the end mutated thread about something else (W&B I recall) Just so that folk know, there is a page on the EarthX website

I floxed 4 screws that have the wide base (like some use for the ailerons) to the Pilot side of the canopy frame for attachment of a ram ball mount.

Is anyone successfully using an iPad mount that uses a suction cup attached to the instrument panel? I am shopping for one and would like to hear recommendations from within the group. Thanks, Andrew

Is there an alterrnative to cleveland brakes that work better than 30-9 that works better? would like something that has the same bolt pattern. Billy Rose

Folks: As has been discussed a number of times, there are many things that can contribute to nose gear shimmy. Here's a movie of one of my customer's Long-EZ nose gear shimmy: https://youtu.be/ut0dLnD

I am shopping for a travel / rain cover for my Cozy MKIV that is usually in the hangar. Bruce's Covers was recommended to me by Russ. Any other options? Does anyone have a cover they aren't using that

Foks: This month's AOPA Pilot Magazine has a good article by Mike Busch (what's new) regarding operating LOP and NOT using EGT to get there. It's on page 93 of the January 2023 edition, and is also on

Marc Zeitlin wrote: This month's AOPA Pilot Magazine has a good article by Mike Busch (what's new) regarding operating LOP and NOT using EGT to get there. I THINK I've been using Mike's leaning techni

Folks: Due to Solon MFG running out of the standard 3/8" Prop Bolt Belleville Washers and having a 1000 quantity minimum for a new order, I've found two replacement washers that can be used - one from

Folks: So I'm pretty sure (although I'll be verifying this in the next few days) that I've got a loose intake tube into the sump on an O-360-A2A. I BELIEVE that the swaging tool to re-swage the tube i

For those that need more speed and want a real short runway https://www.youtube.com/watch?v=rqPRk-3-jPE ... Sweet dreams and flying machines in pieces on the ground... Dale http://www.long-ez.com ====

Folks: I've got two old passive Peltor headsets that I have no need of. First $10 plus shipping (USA only) gets them. Shipping would probably be ~$30 or so, I'm guessing. -- Marc J. Zeitlin marc_zeitl

I’ll take them both for my Cozy Andrew Anunson

Pros vs Cons from the group?

Done the unthinkable a while back and landed nose heavy. Looking for a front gear leg and the weldiment that the front nose gear mounts too. I can't find a part number for it. It's a 4130 welded part.